Precision and AR Rifle Case (Gen-2)

From: $248.95

Free ShippingFree Shipping* / prime eligible

Fits Precision Rifle, AR15/AR10 Rifle & Pistol

  • Holds one Precision Rifle and one AR-15 or AR-10 Rifle, plus a semi-automatic pistol
  • Holds 1 rifle magazine & 2 pistol magazines
  • Accommodates all major scopes & optics that fall within the diagrams' dimensions
  • Fits angled foregrips, lasers, or flashlights mounted directly under the rail of the rifles
  • Max pistol length 8 5/8"
  • Does not accommodate side attachments or larger bipods on any of the firearms
  • Does not accommodate 26" Barrel Ruger Precision Rifles, such as the RPR Lapua Magnum
  • Compact design leaves no wasted space
  • 2 Hydro absorbent silica gel canisters included to help prevent rust
  • Comes with divider piece of foam to separate rifles from each other
  • Waterproof accessory box included for your small items
  • Foam insert is (closed cell) military grade polyethylene which can be wiped clean
  • Integrated wheels for easy transport
  • Case is Airline Approved for checked luggage
  • Gen-2 Upgrades Include:
    • Stainless steel added to padlock points for added security
    • Orange peel texture added to exterior finish to minimize scratches
    • Structural ribs added to outside of case for increased durability
    • 3rd handle added to wheel side for 2 person carry
    • Front handle length increased to help counter balance off center weighted loads
    • Wide bodied snap latches that can be used with gloves

Padlockable (with customer supplied padlock)

Precision and AR Rifle Case (Gen-2) - Available at Amazon
Categories: , , , SKU: 30-TT9B-RUIF
Precision and AR Rifle Case (Gen-2)
YW-PREAR-TOP-2
YW-PREAR-TOP-1
YW-PREAR-RIGHT-LOW
precision-rifle-ar-rifle-case-diagram-combined-rev2
YW-PREAR-LEFT-LOW
YW-PREAR-RIGHT-MAIN
YW-50IN-WHEELS
YW-50IN-PADLOCK
YW-50IN-PURGE-VALVE
YW-50IN-FRONT-DOWN
20200530_104108
20200530_102131
20200530_101633
20200530_101128 (2)
20200530_101021
20200530_095304
precision-rifle-ar-rifle-drawing-big

Description

Maximum Allowable AR15/AR10 Dimensions:

The Case Club Precision and AR Rifle Case (Gen-2) is a rugged, hard-sided solution meticulously engineered to secure and protect a precision rifle, an AR15 or AR10 rifle, and a semi-automatic pistol. Its custom-cut, closed-cell polyethylene foam interior ensures a precise fit, safeguarding firearms and accessories from movement and impact during transit.

Designed to accommodate rifles with mounted optics, angled foregrips, lasers, or flashlights under the rail, this case also includes dedicated spaces for one rifle magazine and two pistol magazines. A divider piece of foam separates the rifles, preventing contact and potential damage. The included waterproof accessory box provides secure storage for small items, while two hydro-absorbent silica gel canisters help prevent rust.

Constructed to withstand harsh conditions, the case is waterproof, dustproof, and airline approved for checked luggage. Integrated wheels and multiple handles facilitate easy transport, and stainless steel reinforced padlock points enhance security. The Gen-2 upgrades feature an orange peel exterior texture to minimize scratches, structural ribs for increased durability, and wide-bodied snap latches operable with gloves.

Protect your investment, buy Case Club.

Disclaimer: This case has been specifically designed and tested to accommodate one precision rifle, one AR15 or AR10 rifle, and one semi-automatic pistol. Firearms with side attachments, larger bipods, or precision rifles with 26″ barrels, such as the RPR Lapua Magnum, may not fit properly. For the best fit and protection, use this case with firearms that fall within the listed dimensional guidelines.

 

Product Specifications

Interior Dimensions50.30"L x 13.50"W x 5.00"H
(1,278mm x 343mm x 127mm)
Exterior Dimensions52.75"L x 16.00"W x 6.00"H
(1,340mm x 406mm x 152mm)
Shipping Weight30.00 LBS (estimated weight of the product with packaging such as a cardboard box)
(13.61 kg)
CharacteristicsWaterproof, Shippable, Crushproof, Outdoor Use
HardwareWheels (Tilt Wheels), Padlockable, Hinged Lid, Pressure Equalization Valve
Rifle / Shotgun TypeAR Pistol, AR10 Rifle, AR15 (Short Barrel), AR15 Rifle, Precision Rifle, Ruger Precision Rifle, Savage 10BA, Savage 110BA
Pistol TypeFits Semi-Autos
Case MaterialPlastic
Manufacturing MethodPrecision Cut, Injection Molded
Manufacturing OriginUnited States of America
Extended TitleFits Precision Rifle, AR15/AR10 Rifle & Pistol
Quantity of Long Guns2
Condition New | Refurbished
SKU 30-TT9B-RUIF

Precision and AR Rifle Case (Gen-2)'s Pre-cut Template

Precision and AR Rifle Case (Gen-2) - Videos

Case Club Precision & AR Rifle Case - Overview

Case Club Precision & AR Rifle Case - Overview - Video

Case Club Hydro Absorbent Silica Gel Video - Overview

Case Club Hydro Absorbent Silica Gel Video - Overview - Video

Customer Questions

  1. Q Would it be possible to put a tactical shotgun with similar dimensions in place of the AR? answer now
    Asked by Charlie on November 30, 2020 12:53 pm
    Answered by the admin It is possible, but important to know what you would be getting yourself into. The foam is of course cut in the profile of an AR15/AR10. Even if the shotgun is the same length it can be assumed the profile is different from the cutout which will require you to modify the foam to fit the shotgun. It is doable, but the Velcro straps may not perfectly line up nor will the overall insert be easy to make look professional. For those reasons, purchasing this case to work with a shotgun is not recommended.
  2. Q Does the foam in the bottom come precut? I saw a picture where the top was cut out but not the bo... answer now
    Asked by Mark Clothier on February 25, 2020 8:34 pm
    Answered by the admin

    Yes, the foam in the bottom does come precut. The image you saw was likely the one below which is showing the removable foam pad that sits on the bottom rifle so the two rifles don't touch when the case is closed. That piece is 1/2" thick and is completely removable.

    This case would not fit an AR in the bottom. For that setup please see our 2 AR Rifle Case which would fit an AR15/AR10 in the lid and the base.
  3. Q Would this case fit a M1A with Sage International EBR chassis? I have a shorter barrel so the len... answer now
    Asked by Ryan on December 18, 2019 8:42 am
    Answered by the admin Looking at the Sage International EBR chassis for the M1A, it looks a little too different than the case's rifle cutout to fit properly. The M1A and the EBR Chassis are untested in this case, but it looks like the extension rails of the stock, and the charging handle of the M1A, may present issues. Overall I do not suspect that the M1A with Sage International EBR chassis would work well in the case.
  4. Q What case would be the best fit for a Ruger Precision 6.5 Creedmoor and a AR 300 blackout? answer now
    Asked by Michael Barrett on November 26, 2019 5:19 pm
    Answered by the admin

    Please start by measuring the length of your rifles. If the Ruger Precision 6.5 Creedmoor does not exceed 50.57" long & the AR300 blackout does not exceed 42.40" long then this case would be the best choice. It is important to verify the dimensions of the rifles before purchasing the product to ensure a compatibility. If neither rifle exceeds those max dimensions then this case will work great.
  5. Q Can you purchase only the precision foam inserts? answer now
    Asked by Ching Yu on October 11, 2019 10:46 pm
    Answered by the admin

    Unfortunately, we don't sell the foam separate from the case.
  6. Q Can this case be ordered with the foam not precutout? And the foam not glued to any part of the c... answer now
    Asked by Jorge Toro on July 6, 2019 9:20 pm
    Answered by the admin

    Yes. This case can be ordered as a generic shipping case that has uncut foam. Be advised the foam layer thickness will be different then this case & there will be no Velcro straps in the lid, but rather generic convoluted foam. That version of the case can be found here: Long Universal Rifle Case
  7. Q Are you guys selling this exact case through Amazon? answer now
    Asked by Charles green on March 3, 2019 12:02 pm
    Answered by the admin Yes. You can purchase this case on Amazon here: Precision & AR Rifle Case
  8. Q Can a SCAR 17 fit in the AR location? answer now
    Asked by Greg on March 2, 2019 7:27 pm
    Answered by the admin

    If you are willing to make foam modifications with the included razor knife you could make it work. Be advised, not all the Velcro holes will line up. It looks like the Scar covers 2 of the Velcro exit points. Here is an illustration of what you would be working with. Colored lines are the template, black lines are the Scar. If you are handy and willing to spend the time it would work. If modifications are not something you would feel comfortable doing then I would advise against this product.
  9. Q Will this case fit a RUGER Precision .338 Lapua Mag? Length wise is not my concern. The case is p... answer now
    Asked by Rusty on March 1, 2019 5:05 pm
    Answered by the admin

    The Case Club Precision and AR Rifle Case can hold a .338 Lapua Magnum Ruger Precision Rifle provided the rifle does not exceed the specs of the "Maximum Dimensions" diagram. The rifle cutout may not perfectly hug the contours of the .338 as well as smaller Ruger Precision variations, but (as seen with the non-Ruger rifle images on the product page) the foam is built to accommodate slightly different shapes as well.

    The case can also hold up to two 5 round .338 Lapua Magnum magazines naturally in the bottom left pocket of the case. For 10 round .338 magazines, the user may need to remove the adjoining convolute foam in the lid of the case to free up some extra space.
  10. Q Do you ship to Austria / Europe? answer now
    Asked by Nok on January 28, 2019 11:00 am
    Answered by the admin

    The international shipping options were just updated for this product so it now can ship to Austria & Europe. Be advised the shipping cost will be expensive.
  11. Q Is there a pressure relief valve on this case? answer now
    Asked by J on January 18, 2019 6:58 pm
    Answered by the admin

    Yes, there is a pressure release valve located on the bottom of the case.
  12. Q Can I fit a M1A scout rifle in the precision rifle part of the case? answer now
    Asked by Brian P Sheaffer on November 5, 2018 4:19 pm
    Answered by the admin

    The M1A rifle will technically fit in the precision rifle area, but there will be extra space left over that could be considered awkward. Below is the M1A overlaid on the existing cutouts. The pink lines make up the M1A scout where as the black lines are the existing cuts already made in the foam. You will have to be the judge whether that is acceptable.
  13. Q Can you customize this case to be double 48" rifles? answer now
    Asked by CLAUDIOI FUNES on August 16, 2018 8:04 pm
    Answered by the admin

    This case can be customized to fit longer a longer rifle however any changes would be considered a custom foam insert which would increase the price. Custom foam generally adds about $200 extra to the product price which accommodates engineering time and machinery setup for a single case. If that is within budget feel free to reach out so we can guide you through the process: 877.412.2737
  14. Q can these cases be ordered without precut foam inserts? answer now
    Asked by Shane on July 11, 2018 6:52 am
    Answered by the admin

    They sure can. This case shell can be found here: https://www.caseclub.com/product/case-club-cc108187pl-case/

Send me a notification for each new answer.

Related products

Optional Accessories …